How to clear paper jam from scansnap s1500?

  1. Remove the document from the ADF paper chute (cover).
  2. Pull the ADF release tab towards you to open the ADF top section.
  3. Open the top cover and the output guide.
  4. Clear any foreign matter from the inside of the ScanSnap.
  5. Close the ADF top section.
  6. Close the top cover and the output guide.

Additionally, how do I reset my ScanSnap s1500?

  1. Press in the home screen on the touch panel of the ScanSnap to display the [Settings] screen.
  2. Press to display the [Scanner settings] screen.
  3. Press [Reset ScanSnap settings].
  4. Press the [Initialize] button.

Considering this, how do I fix my ScanSnap s1500? Close the ADF paper chute to turn off the ScanSnap. Wait at least 5 seconds and open the ADF paper chute to turn on the ScanSnap. If the icon status still indicates “Not Communicating”, unplug the USB cable from the computer or ScanSnap, wait 5 seconds and reconnect the USB cable.

In this regard, how do you unjam a Fujitsu scanner? If you still cannot remove the document, press the [Scan/Stop] button on the ScanSnap for more than 4 seconds while keeping the top cover open. This rotates the feed roller and the eject roller, which will help you remove the document easier (rollers keep rotating while the button is being held down).

See also  Question: How to set epson printer 2540 to only print from one computer?

Beside above, how do I remove paper jam from ScanSnap ix500?

  1. Remove the document from the ADF paper chute (cover).
  2. Pull the ADF release tab to open the ADF top section.
  3. Remove the document inside the ScanSnap.
  4. Close the ADF top section until it clicks. When the error is cleared, the [Scan] button flashes in purple twice.
  5. Load the document again, and press the [Scan] button.

Charge the battery. Connect a USB cable to the USB connector of the ScanSnap and the USB port of the computer that is turned on.

How do you restart a ScanSnap?

Restart your ScanSnap. Turn off your ScanSnap, wait at least 5 seconds and then turn it on again. If the icon status is not changed, unplug the USB cable from the computer or your ScanSnap, wait for 5 seconds, and then reconnect the USB cable.

How do I turn off ScanSnap ix1500?

Close the ADF paper chute (cover) of the ScanSnap to turn the power off. Close the feed guide of the ScanSnap to turn the power off. The ScanSnap is turned off by pressing the [Stop] button for more than 3 seconds until the power LED of the ScanSnap is turned off.

How do I use my ScanSnap S1500?

How do I connect my ScanSnap S1500?

  1. Use the USB cable which has been supplied with the scanner when you connect the scanner to computer.
  2. Wait at least 5 seconds when you reconnect the power cable or open/close the cover.
  3. Set High color for the display.
  4. ScanSnap may not work if it is connected to the USB port on the keyboard or the monitor.
See also  How to establish wireless connection to printer without the printer software cd?

How do I clear a paper jam in ScanSnap?

  1. Remove the document from the ADF paper chute (cover).
  2. Pull the ADF release tab towards you to open the ADF top section.
  3. Open the top cover and the output guide.
  4. Clear any foreign matter from the inside of the ScanSnap.
  5. Close the ADF top section.
  6. Close the top cover and the output guide.

How do I clean my ScanSnap?

How do you unjam a scanner?

This particular issue starts out looking like a ordinary jam – basically, the scanner keeps getting “stuck” – and the usual remedy is to hold down the power button for two seconds, which in turn runs the motors and expels most jammed documents.

How do you scan thin paper?

  1. Step 1: Light Image on the Front Side, Bold Print on the Back.
  2. Step 2: Cover the Back of the Page With Heavy Black Paper.
  3. Step 3: Bleedthrough Is Minimized.
  4. 2 Comments.

What does orange light on ScanSnap mean?

When the Wi-Fi indicator of the ScanSnap is lit in orange, it indicates that the communication with a wireless access point is disconnected. Check that the power of the wireless access point is on, and then connect the ScanSnap to the wireless access point.

Why is ScanSnap flashing blue?

If the light is flashing, it is probably because the ScanSnap software is either not installed or not properly installed. … If you have successfully loaded the Snap Scan software, a flashing blue light indicates the device is getting ready to scan.

See also  How to get label printer from ups?

How do I set up wireless ScanSnap?

  1. Start the ScanSnap Cloud application.
  2. Tap. on the main screen.
  3. Tap [Settings].
  4. Tap [Add wireless access point/router].
  5. Select a ScanSnap scanner that you add a wireless access point to.
  6. Enter the password for your ScanSnap account.
  7. Tap [Authenticate].
  8. Tap [Add wireless access point/router].

Back to top button